Remedial waterproofing & concrete repair services

CAWS delivers specialised remedial works across Western Australia for commercial, strata and residential buildings. Every service starts with an inspection, so we fix what actually failed.

01

Remedial Waterproofing

Investigation and rectification of failed membrane systems on balconies, podium decks, rooftops, planter boxes and internal wet areas. Works can include membrane replacement, substrate preparation, falls correction and upgraded detailing at drains, upturns and junctions. We focus on system compatibility and compliance with the relevant Australian Standards and the NCC, and coordinate making good of ceilings damaged by water and finishes once the leak is fixed.

On site: our crew rolling out a waterproof deck coating on a car park roof.

What a waterproofing membrane is actually made of.

A lasting membrane is built in layers, each with a job to do.

12345
  1. Prepared substrateGround back, cleaned and repaired so the system bonds to sound concrete.
  2. PrimerSeals the surface and gives the membrane something to grip.
  3. ReinforcingBond breakers and reinforcing tape or fabric at corners, joints and drains, where movement and failures concentrate.
  4. Membrane, two coatsBuilt up to the specified thickness. One thin coat is where many cheap jobs fall short.
  5. FinishTiles on a bed, or a trafficable topcoat, protecting the membrane underneath.

A membrane is a system. Skip one layer and the rest can't make up for it.

Waterproofing from the inside when the outside can't be reached.

The best fix is on the side the water comes from. When that face is buried or out of reach, we work from the inside.

Ground waterPOSITIVE SIDENEGATIVE SIDECrystalline treatmentapplied to the inside faceCrystals grow into poresand fine cracksOutside membrane: preferred,but often buried or built to a boundary

Fixing a leak from the side the water comes from is always the better option, and it's our first choice. When that face can't be reached, crystalline waterproofing such as Xypex is applied to the inside. It reacts with moisture and the concrete to grow insoluble crystals in the pores and fine static cracks, holding water back even under pressure. On brickwork it's applied as a crystalline render, built up in layers. The crystals take around a month to fully develop, and moving cracks still need injection or a flexible joint.

CAWS crew applying Xypex crystalline waterproofing to a basement wall
On site: Xypex going onto a basement wall.

More about remedial waterproofing →

02

Concrete Cancer & Spalling Repair

Treatment of corroding reinforcement, spalling concrete (commonly called concrete cancer) and cracking caused by moisture and exposure. Repairs include breakout, steel treatment, reinstatement with suitable repair mortars and protective coatings, plus galvanic anodes where they will extend the life of the repair.

How concrete cancer happens

01Protected

High alkalinity keeps a protective layer on the steel.

02Salt and CO2 get in

Sea air and carbon dioxide work through the concrete cover.

03Steel rusts and swells

Rust takes up several times the space of the steel and cracks the concrete.

04Concrete spalls

The cover breaks away, letting in more water and speeding up the damage.

Spalled concrete with rusted reinforcement exposed
→What it looks like

A spalled slab edge with the rusted steel exposed.

Galvanic anodes, when a project specifies them.

An extra option we install on request, not something every repair needs.

On some projects, usually where an engineer or the project specification calls for them, zinc galvanic anodes are installed with the concrete repair to give the surrounding steel extra protection. Most repairs don't need them, and a properly executed patch repair is the right answer for most jobs. When a project does specify anodes, we install them.

Rows of galvanic anodes being installed across a car park deck
On site: galvanic anodes installed across a car park deck.

More about concrete cancer & spalling repair →

03

Crack Injection

Epoxy and polyurethane injection systems to restore structural continuity or stop active water ingress through cracks in slabs and walls.

Why patching a crack isn't the same as sealing it.

A filled crack looks fixed from above. What matters is what happens underneath.

SURFACE PATCHFiller on toponlyCrack stillopen belowWater gets through

Surface patching covers the top of the crack. The crack stays open underneath, so movement reopens the patch and water keeps tracking through.

PRESSURE INJECTIONInjectionportsResin fillsfull depthSealed through

Pressure injection pumps resin through ports drilled into the crack, filling it through its full depth. Epoxy resin bonds dry, non moving cracks back together. For leaking cracks, water reactive polyurethane stops the flow, usually followed by a flexible resin for a permanent seal.

More about crack injection →

04

Balcony & Podium Restoration

Full balcony and podium restoration that combines membrane renewal, concrete repair and detailing upgrades in one coordinated scope. That means fewer trades, less disruption and a system where every layer works together.

05

Structural Strengthening

Where an inspection finds a structural deficiency, we work with structural engineers on a strengthening design, including carbon fibre reinforcement, and install it to the engineer's specification and the carbon fibre system requirements.

How carbon fibre strengthening works.

Strengthening adds capacity to an existing structure without rebuilding it.

LoadTensionCarbon fibre laminate bondedto the underside with epoxyExisting reinforcementinside the beamFibre wrapconfinesthe columnBeam or slabColumn

We're one of the few remedial contractors in Perth offering carbon fibre strengthening. Carbon fibre is many times stronger than steel for its weight. Bonded to the face of a beam or slab that bends under load, it adds tensile strength. Wrapped around a column, it confines the concrete. Every design comes from a structural engineer, and we install it to their specification.

More about structural strengthening →

06

Decorative Flake & PVC Coatings

Durable decorative flake and PVC waterproofing coatings for balconies, alfresco areas, garages and walkways. Easy to clean, tough and available in a range of colours and blends.

More about decorative flake & pvc coatings →

07

Rising Damp & Damp Course Injection

Diagnosis and treatment of rising damp in brick and masonry walls: a new chemical damp course injected into the mortar bed, salt damaged render removed and replaced with a waterproofing render.

More about rising damp & damp course injection →

Common questions

Questions we get asked a lot.

Do all the tiles need to come up to fix a leaking balcony?

Not always. It depends on why it's leaking. Some leaks come from a failed junction, drain or seal that can be repaired locally, while a failed membrane under the tiles usually means lifting them. We inspect first so the scope matches the problem.

Can you waterproof a basement or wall from the inside?

Yes. When the outside face can't be reached, we can treat concrete and brickwork from the inside with crystalline waterproofing such as Xypex. Working from the outside is always preferable, so we'll tell you which approach is possible on your building.

Does every concrete cancer repair need galvanic anodes?

No. Most repairs do not need them. Galvanic anodes are usually installed when an engineer or the project specification calls for them, and we install them when it does.

Can any waterproofing membrane be left exposed to the sun?

No. Under tile membranes are made to be covered by tiles, a screed or a topcoat, while UV stable membranes are made to be the finished surface. Using the wrong grade is a common cause of early failure, so we match the product to the exposure.

Do you offer carbon fibre strengthening?

Yes. We're one of the few remedial contractors in Perth offering carbon fibre strengthening. Every design comes from a structural engineer, and we install it to their specification.

Do you work outside Perth?

Yes. Most of our work is across the Perth metro area and Peel, and we also take on regional projects, including in Bunbury and Geraldton.

What do you need from me for a quote?

A short description and a few photos are the best start: a close up of the problem and a wider shot showing where it is. You can upload them with the quote form, or call us on 0447 744 005.

Choosing the right system

The right system for each part of the building.

Different parts of a building face different conditions: full sun, foot traffic, cars, or water pushing in from the ground. That's why we don't use one product for everything.

1Exposed roof terrace2Plant room roof3Balconies3Wet areas4Car park deck5Basement wallsWaterproofing system6Inside basement walls
1

UV stable polyurethane

Usually solvent based, UV stable

Our premium choice where the membrane is the finished surface. UV stable grades are made to sit in full sun long term, and walkable areas get an aliphatic topcoat with slip resistant aggregate. The result is seamless and holds its colour on roofs, terraces and walkways.

  • Exposed to sun
  • Foot traffic
  • Premium finish
2

Torch on sheet membrane

Modified bitumen sheets

Sheets made in a factory and welded with heat at the laps, so the thickness is consistent everywhere. A tough choice for plant rooms, large flat roofs and areas that will be covered by pavers or ballast.

  • Large flat roofs
  • Under pavers
3

Reinforced water based polyurethane

Water based, reinforced

The workhorse under tiles and screeds on balconies, podiums, planters and wet areas. Low odour suits occupied buildings. Under tile grades aren't made for long sun exposure, so they need tiles, a screed or a UV topcoat over them.

  • Under tiles
  • Low odour
  • Must be covered
4

Trafficable deck coating

Polyurethane or epoxy system

Built for car park decks and ramps, with slip resistant aggregate and a tough topcoat that takes vehicle traffic and line marking.

  • Vehicle traffic
  • Slip resistant
5

Crack injection

Epoxy and polyurethane resins

For basements, retaining walls and slabs. Epoxy bonds dry, non moving cracks back together. For leaking cracks, water reactive polyurethane stops the flow, usually followed by a flexible resin for a permanent seal.

  • Below ground
  • Active leaks
6

Crystalline waterproofing

Negative side, concrete and brick

When the outside face can't be reached, like a basement built to a boundary, we treat the wall from the inside. It grows crystals in the pores and fine cracks. Working from the outside is always preferable, but it isn't always possible.

  • Negative side
  • Below ground
  • Brick and concrete
No single product suits every job. Even within one brand, some polyurethanes must be covered while others are made for full sun, and using the wrong grade is a common cause of early failure. We choose the system after inspection, based on sun exposure, traffic, the substrate, how the building is used and your budget.

Not sure which service you need?

Describe what you're seeing, add a few photos, and we'll help work out the right scope.

Request a Quote